Van lõi là phần cốt lõi của một vòi nước, nó được sử dụng để kiểm soát on / off và dòng chảy của nước.
Thân máy là bộ phận cơ thể chính của một vòi nước, đó là khung lắp đặt các bộ phận kiểm soát nước vào / ra / dừng.
Bong bóng được sử dụng để kiểm soát tất cả các yếu tố của nước ra như hình dạng, dòng chảy và áp lực để làm cho nước đi ra mà không cần bifurcate, cảm thấy nhẹ nhàng và trông sang trọng.
Bubbler có hai loại phổ biến, một là tiếp xúc, và một trong những ẩn. Lắp vòi nước, vòi nước có thể trở nên sạch sẽ, tiện lợi, chu kỳ sống lâu và chống rỉ tốt.
Tay cầm là một phần cho người sử dụng để điều khiển lõi van, bật / tắt vòi nước và nó cũng có thể điều chỉnh dòng chảy.
Van chuyển đổi có thể thay đổi đầu vào cấp nước, có 2 van thay đổi hoặc 3 van thay đổi, nó cũng có thể thay đổi tự động hoặc bằng tay.
Based on the structure, the closest section can be divided into:
The latest division
The separation tank of the closest type is separated from the pedestal. The water tank is connecting the back of the pedestal with some tightening screws. There are some sealing resin between the pedestal and the water tank that prevents the water from dripping out.
Features of the most recent Split type: The water tank is installed in a higher place, higher water level, which means that the hydraulic pressure is heavier, so it is easier to clean the nearest. Because the water tank and the pedestal have separate production lines, it produces higher rates of production and is easier to produce, so it’s cheaper.
The nearest
This type of wheel is the vehicle is integrated, no integral parts, so it looks beautiful. However, the more production, the lower the finished ratio, resulting in higher prices on the market.
Wall-mounted type near
There are two types of wall mounts, the wall type and the ground. It uses a water drain valve instead of a water tank, saving time, can be used continuously and convenient to clean. It is hidden under the water tank with a clean and neat look, but is hard to replace.
The nearest unloading system can be divided into:
Type wash
Use the impact force of the water to discharge the nearest water. The closest one is a standing wall, with limited water inside the urinal. This type of product is the main structure of Europe, the biggest advantage is its water flow less than other types, however, its noise is larger. Installation is more elastic, the requirements of space are loose.
Type siphon
Its structure is like other fishing systems, the only difference is that our supply pipes are buried underground and lying down. To adapt to the requirements of pipelines, water tanks and urinals is an integrated device. Its greatest advantage is the use of whirlpools and syngas: whirlpools can provide force to the heart, rotate the wastewater into the vortex, then dispose of it through draining power, the entire flushing process. fast and full and less smells and noise.
Type siphon
Siphon-jet type improved from siphon type. The change is that it adds a jet port, which can improve the strength of the water stream, while it improves the rate of waste water discharge. The water cover is larger than the other types, it has a strict standard of deep water, and it is good to reduce odor and prevent splash. Moreover, jet stream water is under water operation so noise is restricted.
Based on the space between the device and the wall, the nearest can be divided into:
Land treatment (S): 200mm
Land treatment (S): 305mm
Land treatment (S): 400mm
Wall to discharge (S / P): Flexible space (can be discharged through the wall or the ground).
Table type: It can also be divided into types on the table and in the table. In the table table is installed in the table, easier to clean and wash.
The basin has three holes:
Faucet; Spillway; Loss of discharge.
Under tap settings, the tap installation hole can be divided into:
No holes: Typically this is for tubs in the table, tap is usually mounted on the wall or on the table.
A hole: Cold water and hot water enter the same pipe, with the fibers at the bottom of the tap, which can stabilize the hole through the particles.
Three holes: The holes have two sizes: 4 inch and 8 inch. It can be set up with hand washers or hand washers (including 4 inch and 8 inch two sizes). Cold water and hot water enter the various pipes, the plane on either side of the faucet.
Baths can be divided into:
Based on the model:
Skirts or skirts
Based on shape:
Hearts, circles, ovals, squares and triangles.
Based on the function:
Common bathtub, massage bathtub. Baths can also be divided into bubbles, hydrotherapy and air therapy.
Based on the material:
Cast iron bath: Using the molding process, produce rough and then glaze at high temperatures, forming a hard enamel coating and anti-wear.
Characteristics: gloss and hard, anti-wear, low noise, stable, durable, prevent waste water, easy cleaning and long life cycle. Its heat preservation is good, it is suitable to take a long bath. However, it is too complex and expensive to produce, has limited shape and limited color.
Acrylic Bath: Another name is polymethyl methacrylate, also known as organic glass.
Properties: Shiny surface, hard, durable, heat resistant, heat preservation and easy to clean. The strongest feature of this bathtub is its robust toughness that it can create many different shapes that can satisfy the majority of consumers.
Steel plate tank: This product is manufactured by 2mm thick steel plate through stamping and enamel.
Features: On the surface are glazed and glazed, most of these bathtubs are often shallow depths, and high cost of stamping, as a result of limited shape, simple and lack of heat preservation.
Artificial stone: The main material is artificial stone, polished by hand.
Characteristics: This type of material has good stability, stable life cycle, durability and durability. It is durable, easy to clean, easy to maintain and durable.
If you don't see the answer for your question, send us a message and we will get to you as soon as possible.
Contact Us